Unsolved Dell r720 and Hitachi Drive
-
Specs:
Dell r720 surplused
Hitachi HUC106060css600 512 drivesI admit - I've realized that the last server I had to physically touch was likely back in 2009. While I have worked with systems, I've not had to build or rebuild an array in a very long time. So I am a tad rusty.
System does see these drives - I have a full complement of sixteen to fully populate the two bays. However I have run into a slight issue with these drives I hadn't had to work with previously as technology has changed.
These drives are per the details above 512/512e and the r720 doesn't want to 'accept' them. While the PERC does see them, they are all marked as BLOCKED.
Now, I understand that sector size is set and cannot be changed - I rather expected to find the correct firmware needed to update the PERC to allow these drives to be used...
I do see that Dell has the driver for this drive - but reading the details about it seems to point at an OS side issue and not the PERC.
I fully expect that I am simply overlooking the solution because I am looking at or for the wrong information.
-
@gjacobse said in Dell r720 and Hitachi Drive:
Specs:
Dell r720 surplused
Hitachi HUC106060css600 512 drivesI admit - I've realized that the last server I had to physically touch was likely back in 2009. While I have worked with systems, I've not had to build or rebuild an array in a very long time. So I am a tad rusty.
System does see these drives - I have a full complement of sixteen to fully populate the two bays. However I have run into a slight issue with these drives I hadn't had to work with previously as technology has changed.
These drives are per the details above 512/512e and the r720 doesn't want to 'accept' them. While the PERC does see them, they are all marked as BLOCKED.
Now, I understand that sector size is set and cannot be changed - I rather expected to find the correct firmware needed to update the PERC to allow these drives to be used...
I do see that Dell has the driver for this drive - but reading the details about it seems to point at an OS side issue and not the PERC.
I fully expect that I am simply overlooking the solution because I am looking at or for the wrong information.
Are you looking at the PERC bios screen? If it's in standard RAID mode, that's where you need to setup the array.
Hotkeys are always different. If you have access to the iDRAC, you should be able to boot directly into the RAID bios from that. I have an even older R620 still in use as my home lab box, and that's normally how I access the PERC bios when needed.
You're reminding me that I really should see about upgrading my home lab box.
-
Sadly,.. While I can access the PERC I cannot access the iDRAC;
iDRAC settings Version: 1.65.65.04
SWC0700: iDRAC is not ready. The configuration values cannot be accessed.The PERC sees all drives installed, but the State is Blocked.
-
iDRAC -
Ended up being short lived excitement when I came in last night to see that I could access the LifeCycle controller and was able to get the iDRAC connected.
Used the reboot option and that was it I suppose... Back to LifeCycle controller being disabled and the iDRAC being inaccessible.
Odd also is that it seems to only allow one of the four main NICs over the iDRAC NIC - Has it been so long since I worked on something at this level that I've misconstrued some information on how the iDRAC NIC is suppose to work/
-
@gjacobse said in Dell r720 and Hitachi Drive:
iDRAC -
Ended up being short lived excitement when I came in last night to see that I could access the LifeCycle controller and was able to get the iDRAC connected.
Used the reboot option and that was it I suppose... Back to LifeCycle controller being disabled and the iDRAC being inaccessible.
Odd also is that it seems to only allow one of the four main NICs over the iDRAC NIC - Has it been so long since I worked on something at this level that I've misconstrued some information on how the iDRAC NIC is suppose to work/
iDRAC normally has a NIC separate from all the others. Some utilize the same NIC as the main system, but those are the jank version. My R620 iDRAC is a physically separate network port, and all the servers at work are as well.
-
Yes, this unit does have the iDRAC port also, which is why this seems weird…
-
@gjacobse Now that I think about it, you might want to try a bios reset on the iDRAC. I don't know if that will make a difference, but it's corrected issues with them for me in the past.