Pi as a UPS monitor

JaredBusch

And something is broke, but since I followed the directions I had previously wrote in October, that I means I left out something I did.

pi@bna-pwr-pi-01:/etc/nut $ tail -f /var/log/syslog
Feb  2 04:20:42 bna-pwr-pi-01 systemd[1]: Starting Network UPS Tools - power device monitor and shutdown controller...
Feb  2 04:20:42 bna-pwr-pi-01 upsmon[1284]: fopen /var/run/nut/upsmon.pid: No such file or directory
Feb  2 04:20:42 bna-pwr-pi-01 upsmon[1284]: UPS: bnajaredrouter@localhost (master) (power value 1)
Feb  2 04:20:42 bna-pwr-pi-01 upsmon[1284]: Using power down flag file /etc/killpower
Feb  2 04:20:42 bna-pwr-pi-01 upsmon[1286]: Startup successful
Feb  2 04:20:42 bna-pwr-pi-01 upsmon[1287]: Init SSL without certificate database
Feb  2 04:20:42 bna-pwr-pi-01 systemd[1]: nut-monitor.service: Supervising process 1287 which is not our child. We'll most likely not notice when it exits.
Feb  2 04:20:42 bna-pwr-pi-01 systemd[1]: Started Network UPS Tools - power device monitor and shutdown controller.
Feb  2 04:20:42 bna-pwr-pi-01 upsmon[1287]: UPS [bnajaredrouter@localhost]: connect failed: Connection failure: Connection refused
Feb  2 04:20:42 bna-pwr-pi-01 upsmon[1287]: Communications with UPS bnajaredrouter@localhost lost
Feb  2 04:20:47 bna-pwr-pi-01 upsmon[1287]: UPS [bnajaredrouter@localhost]: connect failed: Connection failure: Connection refused
Feb  2 04:20:47 bna-pwr-pi-01 upsmon[1287]: UPS bnajaredrouter@localhost is unavailable
                                                                               
Broadcast message from nut@bna-pwr-pi-01 (somewhere) (Thu Feb  2 04:20:47 2017)
                                                                               
UPS bnajaredrouter@localhost is unavailable                                    
                                                                               
Feb  2 04:20:52 bna-pwr-pi-01 upsmon[1287]: UPS [bnajaredrouter@localhost]: connect failed: Connection failure: Connection refused
Feb  2 04:20:57 bna-pwr-pi-01 upsmon[1287]: UPS [bnajaredrouter@localhost]: connect failed: Connection failure: Connection refused
Feb  2 04:21:02 bna-pwr-pi-01 upsmon[1287]: UPS [bnajaredrouter@localhost]: connect failed: Connection failure: Connection refused
Feb  2 04:21:07 bna-pwr-pi-01 upsmon[1287]: UPS [bnajaredrouter@localhost]: connect failed: Connection failure: Connection refused

JaredBusch

Manually executed sudo start upsd and got a driver error. Fixed typo, rebooted, and it is online.

pi@bna-pwr-pi-01:~ $ tail -f /var/log/syslog
Feb  2 04:27:24 bna-pwr-pi-01 systemd[1]: Reached target Graphical Interface.
Feb  2 04:27:24 bna-pwr-pi-01 systemd[1]: Starting Update UTMP about System Runlevel Changes...
Feb  2 04:27:24 bna-pwr-pi-01 upsmon[737]: Init SSL without certificate database
Feb  2 04:27:24 bna-pwr-pi-01 systemd[1]: Started Update UTMP about System Runlevel Changes.
Feb  2 04:27:24 bna-pwr-pi-01 systemd[1]: Startup finished in 2.052s (kernel) + 10.336s (userspace) = 12.389s.
Feb  2 04:27:24 bna-pwr-pi-01 upsd[733]: User bnaupsmon@::1 logged into UPS [bnajaredrouter]
Feb  2 04:27:31 bna-pwr-pi-01 dhcpcd[698]: wlan0: no IPv6 Routers available
Feb  2 04:27:51 bna-pwr-pi-01 systemd[1]: Time has been changed
Feb  2 04:27:52 bna-pwr-pi-01 upsd[733]: Data for UPS [bnajaredrouter] is stale - check driver
Feb  2 04:27:52 bna-pwr-pi-01 upsd[733]: UPS [bnajaredrouter] data is no longer stale

pi@bna-pwr-pi-01:~ $ sudo upsc bnajaredrouter
Init SSL without certificate database
battery.charge: 100
battery.charge.low: 10
battery.charge.warning: 50
battery.date: 2001/09/25
battery.mfr.date: 2010/12/15
battery.runtime: 14100
battery.runtime.low: 120
battery.type: PbAc
battery.voltage: 27.3
battery.voltage.nominal: 24.0
device.mfr: American Power Conversion
device.model: Back-UPS BR1000G
device.serial: 3B1051X20349  
device.type: ups
driver.name: usbhid-ups
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.version: 2.7.2
driver.version.data: APC HID 0.95
driver.version.internal: 0.38
input.sensitivity: medium
input.transfer.high: 147
input.transfer.low: 88
input.voltage: 126.0
input.voltage.nominal: 120
ups.beeper.status: disabled
ups.delay.shutdown: 20
ups.firmware: 868.L1 .D
ups.firmware.aux: L1  
ups.load: 3
ups.mfr: American Power Conversion
ups.mfr.date: 2010/12/15
ups.model: Back-UPS BR1000G
ups.productid: 0002
ups.realpower.nominal: 600
ups.serial: 3B1051X20349  
ups.status: OL
ups.test.result: No test initiated
ups.timer.reboot: 0
ups.timer.shutdown: -1
ups.vendorid: 051d
pi@bna-pwr-pi-01:~ $

JaredBusch

Unplugged the power and had some good news, some bad.

The WALL commands spammed me, so I know things fired.

The syslog though showed an error about permissions for PIPE/LOCK. See the message about failed to connect to parent.

Feb  2 04:32:33 bna-pwr-pi-01 upsmon[737]: UPS bnajaredrouter@localhost on battery
Feb  2 04:32:41 bna-pwr-pi-01 upssched[805]: Failed to connect to parent and failed to create parent: No such file or directory
Feb  2 04:33:03 bna-pwr-pi-01 upsmon[737]: UPS bnajaredrouter@localhost on line power
Feb  2 04:33:03 bna-pwr-pi-01 upssched[811]: Executing command: ongrid
Feb  2 04:33:03 bna-pwr-pi-01 upssched-cmd: The UPS is now on grid power.

Time to check the permissions.

JaredBusch

Well that would be a problem. Where did the file I made go? I guess the default directory was a bad choice?

pi@bna-pwr-pi-01:~ $ sudo ls -l /var/run/nut/
total 12
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 upsd.pid
-rw-r--r-- 1 root root 4 Feb  2 04:27 upsmon.pid
srw-rw---- 1 nut  nut  0 Feb  2 04:27 usbhid-ups-bnajaredrouter
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 usbhid-ups-bnajaredrouter.pid
pi@bna-pwr-pi-01:~ $

JaredBusch

and there there we go.. changed directory to /etc/nut/upssched for PIPE/LOCK (already corrected instructions above)

WALL spam...

Broadcast message from nut@bna-pwr-pi-01 (somewhere) (Thu Feb  2 04:44:19 2017)
                                                                               
UPS bnajaredrouter@localhost on battery                                        
                                                           
Broadcast message from nut@bna-pwr-pi-01 (somewhere) (Thu Feb  2 04:45:19 2017)
                                                                               
UPS bnajaredrouter@localhost on line power

and the SYSLOG showing the trigger and the command from the shell script.

Feb  2 04:43:24 bna-pwr-pi-01 upsmon[917]: Startup successful
Feb  2 04:43:24 bna-pwr-pi-01 upsmon[918]: Init SSL without certificate database
Feb  2 04:43:24 bna-pwr-pi-01 systemd[1]: nut-monitor.service: Supervising process 918 which is not our child. We'll most likely not notice when it exits.
Feb  2 04:43:24 bna-pwr-pi-01 systemd[1]: Started Network UPS Tools - power device monitor and shutdown controller.
Feb  2 04:43:24 bna-pwr-pi-01 upsd[733]: User bnaupsmon@::1 logged into UPS [bnajaredrouter]
Feb  2 04:44:19 bna-pwr-pi-01 upsmon[918]: UPS bnajaredrouter@localhost on battery
Feb  2 04:44:19 bna-pwr-pi-01 upssched[929]: Timer daemon started
Feb  2 04:44:19 bna-pwr-pi-01 upssched[929]: New timer: onbattwarn (30 seconds)
Feb  2 04:44:49 bna-pwr-pi-01 upssched[929]: Event: onbattwarn
Feb  2 04:44:49 bna-pwr-pi-01 upssched-cmd: The UPS has been on battery power for 30 seconds.
Feb  2 04:45:04 bna-pwr-pi-01 upssched[929]: Timer queue empty, exiting
Feb  2 04:45:19 bna-pwr-pi-01 upsmon[918]: UPS bnajaredrouter@localhost on line power
Feb  2 04:45:19 bna-pwr-pi-01 upssched[937]: Executing command: ongrid
Feb  2 04:45:19 bna-pwr-pi-01 upssched-cmd: The UPS is now on grid power.

JaredBusch

No able to test email right now because there is no way to send SMTP port 25 from my house. I have a VPN to the colo up, and there is a mail relay running there, but it will not accept from outside its LAN.

So I will have to set that up later.

JaredBusch

I'll rewrite this as an actual how to in the next few days.

JaredBusch

@JaredBusch said in Pi as a UPS monitor:

Well that would be a problem. Where did the file I made go? I guess the default directory was a bad choice?

pi@bna-pwr-pi-01:~ $ sudo ls -l /var/run/nut/
total 12
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 upsd.pid
-rw-r--r-- 1 root root 4 Feb  2 04:27 upsmon.pid
srw-rw---- 1 nut  nut  0 Feb  2 04:27 usbhid-ups-bnajaredrouter
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 usbhid-ups-bnajaredrouter.pid
pi@bna-pwr-pi-01:~ $

@scottalanmiller what would be the 'proper' place for these files?

travisdh1

@JaredBusch said in Pi as a UPS monitor:

Well that would be a problem. Where did the file I made go? I guess the default directory was a bad choice?

pi@bna-pwr-pi-01:~ $ sudo ls -l /var/run/nut/
total 12
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 upsd.pid
-rw-r--r-- 1 root root 4 Feb  2 04:27 upsmon.pid
srw-rw---- 1 nut  nut  0 Feb  2 04:27 usbhid-ups-bnajaredrouter
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 usbhid-ups-bnajaredrouter.pid
pi@bna-pwr-pi-01:~ $

If it's me, that's normally forgetting to add the sudo before my favorite text editor. Anything in /dev or /etc requires root privilege. Besides that, dunno. Nano complains at you saying "read only" when you try to save.... yeah, seen that a few more times than I can count.

JaredBusch

@JaredBusch said in Pi as a UPS monitor:

@JaredBusch said in Pi as a UPS monitor:
Well that would be a problem. Where did the file I made go? I guess the default directory was a bad choice?
pi@bna-pwr-pi-01:~ $ sudo ls -l /var/run/nut/
total 12
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 upsd.pid
-rw-r--r-- 1 root root 4 Feb  2 04:27 upsmon.pid
srw-rw---- 1 nut  nut  0 Feb  2 04:27 usbhid-ups-bnajaredrouter
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 usbhid-ups-bnajaredrouter.pid
pi@bna-pwr-pi-01:~ $ 
@scottalanmiller what would be the 'proper' place for these files?

Hey @scottalanmiller you never answered this one. What is 'proper' for this kinda thing.

travisdh1

@JaredBusch said in Pi as a UPS monitor:

@JaredBusch said in Pi as a UPS monitor:
@JaredBusch said in Pi as a UPS monitor:
Well that would be a problem. Where did the file I made go? I guess the default directory was a bad choice?
pi@bna-pwr-pi-01:~ $ sudo ls -l /var/run/nut/
total 12
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 upsd.pid
-rw-r--r-- 1 root root 4 Feb  2 04:27 upsmon.pid
srw-rw---- 1 nut  nut  0 Feb  2 04:27 usbhid-ups-bnajaredrouter
-rw-r--r-- 1 nut  nut  4 Feb  2 04:27 usbhid-ups-bnajaredrouter.pid
pi@bna-pwr-pi-01:~ $ 
@scottalanmiller what would be the 'proper' place for these files?
Hey @scottalanmiller you never answered this one. What is 'proper' for this kinda thing.

Should be /etc/nut. The standard is to put config files in /etc. /dev is generally hardware devices.

gjacobse

@JaredBusch

You could add this little display on your Pi for local status-

https://www.adafruit.com/product/3527?utm_source=youtube&utm_medium=videodescrip&utm_campaign=newproducts

https://cdn-shop.adafruit.com/970x728/3527-04.jpg

scottalanmiller

@gjacobse I like that, it's cute.

travisdh1

@gjacobse Nice find. And only uses 6 pins? I've got a 2.5" display that uses most of the GPIO block

gjacobse

@travisdh1 said in Pi as a UPS monitor:

@gjacobse Nice find. And only uses 6 pins? I've got a 2.5" display that uses most of the GPIO block

The only thing I might do is see if it was possible to rotate the display part 90deg,.. free up the header area for more - OR make a breakout board for all 20 GPIO with the OlED turned...

gjacobse

@JaredBusch

Did you ever get this project finished?

JaredBusch

Aside from alerting, this was working. No, I never circled back to this.

bxdobs

Struggling with getting nut to work with an old APC UPS ... lsusb suggests the UPS USB port is connecting to the PI (it lists the device when plugged in) but can't seem to find the right combination of configurations to allow nut to actually monitor the UPS itself.

tried drivers;
usbhid-usb port=auto
genericusb with type; = 1, 2, 9, or 12 (port=serial1)
apcsmart
apcsmart-old
apcupsd-ups

seems that the ups is just not being found

is there some way to manually poke the USB port (sort of like we used to do with uarts with AT commands)?

gjacobse

@bxdobs said in Pi as a UPS monitor:

Struggling with getting nut to work with an old APC UPS ... lsusb suggests the UPS USB port is connecting to the PI (it lists the device when plugged in) but can't seem to find the right combination of configurations to allow nut to actually monitor the UPS itself.

tried drivers;
usbhid-usb port=auto
genericusb with type; = 1, 2, 9, or 12 (port=serial1)
apcsmart
apcsmart-old
apcupsd-ups

seems that the ups is just not being found

is there some way to manually poke the USB port (sort of like we used to do with uarts with AT commands)?

I actually just went through this about a month or so ago when I set up Ubuntu Server and a APCups. I'm not at the house to pull what I did,... but I heavily referenced this very thread. Yes - where I don't live in Linux CLI as some do, I had to do some trial and error again. but that's part of (re)learning.

bxdobs

Removed the nut installation, config files and did a complete Raspbian upgrade ... Now after reinstalling nut with the bare minimum configuration, it is finally talking to the ups.

Even though I have been technically involved with computer tech going back to the late '70s, this install was certainly not for the faint of heart ... I can understand why people walk away in frustration from this stuff