ML
    • Recent
    • Categories
    • Tags
    • Popular
    • Users
    • Groups
    • Register
    • Login

    Mitel - connection to SIP provider

    IT Discussion
    mitel sip registration
    3
    8
    952
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • D
      Dashrender
      last edited by Dashrender

      Jared and I spent more than an hour trying to get my Mitel 5000 to connect to VOIP.ms.

      Let me start by saying that I have a working connection to Cox Communication for SIP.

      Here are the settings we have so far for VOIP.ms

      MiVoice Office 250 > System > Devices and Feature Codes > SIP Peers > SIP Trunk Groups

      I created Trunk Group 9205
      b1cd9d5a-4d7a-45fe-b47c-1e49e8a27089-image.png

      As noted here, The IP is for chicago2.voip.ms. The call configuration of '2' is based upon the setting that work for Cox.
      The following were changed to Yes

      • Use Peer Address In From Header
      • Disable Domain Validation

      All other settings left as default.
      7285941d-b24a-45d3-b153-6eccfa1fb0e0-image.png

      Again, the same IP as before.
      The Initial Retry Interval was changed to 120 from 60
      All other settings left as default.

      e075f383-9a0c-4ec6-a673-8110498991c4-image.png
      Inbound authentication is left NO
      Set the outbound Username and password to match VOIP.ms subaccount
      (Jared suggested that I use a password containing no special characters)
      All other settings left as default.

      Keep-Alive
      3f01a9dc-f9f2-42bc-943f-ec7725075af9-image.png

      Changed Pinter Interval to 120.
      All other settings left as default.

      Move to
      MiVoice Office 250 > System > Devices and Feature Codes > SIP Peers > SIP Trunk Groups > 9205 > Trunk Group Configuration > Trunks
      74e17ac9-6ee5-417f-968f-5edfa097d6ea-image.png

      Add the number of trunks you have licenses for. While you can add as many trunks as you like, Mitel will only allow you to use them up to the point where you run out of licenses.

      *Note - If you have multiple resources using a license type, SIP for example, All licenses are assigned to the trunks for the lowest numerical SIP Trunk Groups, then the next lowest, etc. This means if you have 23 licenses, and have 23 trunks in the first group, you will have zero left over for your second group. You can delete trunks from the lower numbered group to allow licenses to be usable for the second group. Unfortunately, Mitel doesn't see concurrent usage, only assigned usage.

      All other settings are default.

      With the above settings, I can and do get registered and can make outgoing calls. I cannot make incoming calls - I get a normal busy.

      Then after a period of time (less than 5 mins) the registration will drop and outgoing calls will stop.

      Several settings options were taking from this page's setup recommendations.
      https://support.sip.us/hc/en-us/articles/115001501186-Mitel-5000

      Thoughts?

      *Edit -
      MiVoice Office 250 > System > Devices and Feature Codes > SIP Peers > SIP Trunk Groups > 9205 > Trunk Group Configuration

      8f125bc1-5bb4-4876-819a-4adc0843db9f-image.png

      As seen here, you have to set the Day/Night Ring-In Type to a destination. By default they were set to single with no destination.
      In my case I want them to use my call routing table based on incoming phone number.

      B 1 Reply Last reply Reply Quote 1
      • B
        bnrstnr @Dashrender
        last edited by

        @Dashrender said in Mitel - connection to SIP provider:

        With the above settings, I can and do get registered and can make outgoing calls. I cannot make incoming calls - I get a normal busy.
        Then after a period of time (less than 5 mins) the registration will drop and outgoing calls will stop.
        Several settings options were taking from this page's setup recommendations.
        https://support.sip.us/hc/en-us/articles/115001501186-Mitel-5000

        In the below link Jared sets the maximum retries to 0. Looks like you have it set to 5. Granted that is on freepbx, no idea if this is different from system to system.
        https://mangolassi.it/topic/12327/setting-up-a-sip-trunk-in-freepbx-13/6

        1 Reply Last reply Reply Quote 0
        • B
          bnrstnr
          last edited by

          You don't have super secret SIP-ALG on the "modem"/gateway do you? No double NAT setup? Those are what I just ran into recently.

          What about the "NAT settings" in the first pic?

          1 Reply Last reply Reply Quote 0
          • J
            JaredBusch
            last edited by JaredBusch

            The initial retry can stay 60.

            I meant for you to change the registration refresh interval from 1800 to 120

            D 2 Replies Last reply Reply Quote 1
            • D
              Dashrender @JaredBusch
              last edited by Dashrender

              @JaredBusch said in Mitel - connection to SIP provider:

              The initial retry can stay 60.

              I meant for you to change the registration refresh interval from 1800 to 120

              done - let's see if it stay active now.

              I changed the ping time back to 60 as well.

              1 Reply Last reply Reply Quote 0
              • D
                Dashrender @JaredBusch
                last edited by

                @JaredBusch said in Mitel - connection to SIP provider:

                The initial retry can stay 60.

                I meant for you to change the registration refresh interval from 1800 to 120

                So far, registration seems to be staying up! yeah.. Thanks.

                1 Reply Last reply Reply Quote 0
                • D
                  Dashrender
                  last edited by Dashrender

                  It's been a painful two days, but it's fixed.

                  I've edited the OP with the solution, but here it is just the same.

                  MiVoice Office 250 > System > Devices and Feature Codes > SIP Peers > SIP Trunk Groups > 9205 > Trunk Group Configuration

                  8f125bc1-5bb4-4876-819a-4adc0843db9f-image.png

                  As seen here, you have to set the Day/Night Ring-In Type to a destination. By default they were set to single with no destination.
                  In my case I want them to use my call routing table based on incoming phone number.

                  I found this setup document which pointed me Day/Night Ring-In Type settings.
                  https://enterprise.spectrum.com/content/dam/business/pdfs/services/voip/sip/Mitel MiVoice 250 6.0 Configuration Guide (TWC).pdf

                  1 Reply Last reply Reply Quote 2
                  • D
                    Dashrender
                    last edited by

                    While not related to the SIP function, I don't see any point currently in making a new thread.

                    if you want to add/change things in ARS (Automatic Route Selection) look here
                    1fc36c91-9696-409c-a8f9-8f3bc77090c0-image.png

                    You'll see places to add your new SIP trunk under > Facility Groups > P1500 (or your own numbering scheme) > Trunk Groups/Nodes
                    in the right pane, right click and add.

                    1 Reply Last reply Reply Quote 0
                    • 1 / 1
                    • First post
                      Last post