FreePBX assign commercial module to installation?

JaredBusch

That should match this.

BraswellJay

@JaredBusch said in FreePBX assign commercial module to installation?:

That should match this.

Yep they both match. I didn't know about viewing it through the fwconsole command before but I had gone to System Admin->Activation and the same deployment ID shows there as it does on both the places you mentioned.

JaredBusch

Check you orders in the portal. Click on the circled line item

Click the +

Verify the deployment ID matches.

BraswellJay

@JaredBusch said in FreePBX assign commercial module to installation?:

Verify the deployment ID matches.

It shows as completed in the portal and has the correct deployment ID on the order.

JaredBusch

@BraswellJay said in FreePBX assign commercial module to installation?:

@JaredBusch said in FreePBX assign commercial module to installation?:

Verify the deployment ID matches.

It shows as completed in the portal and has the correct deployment ID on the order.

Does it not show up here then?

BraswellJay

@JaredBusch said in FreePBX assign commercial module to installation?:

@BraswellJay said in FreePBX assign commercial module to installation?:

@JaredBusch said in FreePBX assign commercial module to installation?:

Verify the deployment ID matches.

It shows as completed in the portal and has the correct deployment ID on the order.

Does it not show up here then?

It shows up there, same deployment ID. That's the only place I initially knew to check so I had verified that it was the same as what was on the order, and that has matched all of the other places you've showed me.

JaredBusch

If it is showing correctly in all those places, the modules should be working.

If SysAdmin is activated, it should show more option on the right. Like Email Setup

EPM should look like the lower image.

JaredBusch

What is the status of those modules?

fwconsole ma listonline | grep "endpoint\|sysadmin"

Jared forgot the \ in front of the pipe. Don't be a Jared.

BraswellJay

@JaredBusch said in FreePBX assign commercial module to installation?:

What is the status of those modules?
fwconsole ma listonline | grep "endpoint\|sysadmin"
Jared forgot the \ in front of the pipe. Don't be a Jared.

[root@CEC-freePBX ~]# fwconsole ma listonline | grep "endpoint\|sysadmin"
| endpoint             | 14.0.2.188 | Enabled and up to date                     | Commercial  |
| sysadmin             | 14.0.33    | Enabled and up to date                     | Commercial  |

Here is my current sysadmin and endpoint manager screens:

BraswellJay

@JaredBusch

I think I figured this out. The thing I needed to do was to stop and then start FreePBX.

I did :

fwconsole stop
fwconsole start

When it started back I saw the following as part of the output :

Updating License Information for xxxxxxxx

where the x's were my deployment ID

I'm thinking this must be where it went out and queried and saw I had purchased those two modules.

Both SysAdmin Pro and the Endpoint Manager screens now look like your samples.

Thanks for the help.

One question. When you have purchased these through the GUI instead of the portal as I did do you normally have to restart or does it just figure that out and is immediately available?

JaredBusch

@BraswellJay said in FreePBX assign commercial module to installation?:

@JaredBusch

I think I figured this out. The thing I needed to do was to stop and then start FreePBX.

I did :
fwconsole stop
fwconsole start
When it started back I saw the following as part of the output :
Updating License Information for xxxxxxxx
where the x's were my deployment ID

I'm thinking this must be where it went out and queried and saw I had purchased those two modules.

Both SysAdmin Pro and the Endpoint Manager screens now look like your samples.

Thanks for the help.

One question. When you have purchased these through the GUI instead of the portal as I did do you normally have to restart or does it just figure that out and is immediately available?

It is all handled in a reboot.

I buy these during initial turn up time and as part of that, I will always perform a final reboot before begining the actual configuration. Because one of the turn up steps requires setting the timezone, and that is not applied fully until a reboot.

Honestly, I simply assumed that you had already turned it on and off again.

You could have used

fwconsole restart

or clicked the update activation in the web GUI also.