Ubiquiti ERL script wanted to compare md5 values
-
@JaredBusch said:
looking at what i need to do to send an email. The documentation for ERL sucks as it is mostly community created and the package stuff changed with firmware 1.6.0
Oh shoot, forgot that it was ERL. Might not use the same mail command at all. That's a common syntax, but certainly not the only one.
-
@scottalanmiller said:
Also try it with good md5 sums to make sure it does nothing when they are successfully matched. Just to be sure.
I did.
jbusch@jared:~$ md5sum -c /config/md5test.md5 echo && "Successful test of MD5" || echo "Failed test of MD5" /root.dev/squashfs.img: OK /root.dev/squashfs.o: OK md5sum: echo: No such file or directory Failed test of MD5 jbusch@jared:~$ md5sum -c /config/md5test.md5 && echo "Successful test of MD5" || echo "Failed test of MD5" /root.dev/squashfs.img: OK /root.dev/squashfs.o: OK Successful test of MD5 jbusch@jared:~$ -
The first one "worked" because you put in three commands and the middle one had a typo so failed caused the third one to trigger. You didn't test what you think that you tested.
-
I did earlier then when doing further testing found it easier to use the typo instead of updating the .md5 file repeatedly. guess i could have made a second one for failure testing.. It is late and I am a bit lazy at this point.
-
@JaredBusch said:
I did earlier then when doing further testing found it easier to use the typo instead of updating the .md5 file repeatedly. guess i could have made a second one for failure testing.. It is late and I am a bit lazy at this point.
Only problem is that you are testing the failure of the echo command not of the md5sum in doing that.
-
I was making sure a success worked like i thought because i was thinking that writing it to a system log would be good even on success.
-
Oh no, I think you are right, that syntax should work.
-
Happy now?
jbusch@jared:~$ md5sum -c /config/bad.md5 && echo "Successful test of MD5" || echo "Failed test of MD5" /root.dev/squashfs.img: OK /root.dev/squashfs.o: FAILED md5sum: WARNING: 1 of 2 computed checksums did NOT match Failed test of MD5 jbusch@jared:~$ md5sum -c /config/good.md5 && echo "Successful test of MD5" || echo "Failed test of MD5" /root.dev/squashfs.img: OK /root.dev/squashfs.o: OK Successful test of MD5 jbusch@jared:~$ -
Yes better
Don't forget the 2>/dev/null so you only get the result message.
-
what is the 2 for? it still printed instead of sending the output to /dev/null
jbusch@jared:~$ md5sum -c /config/good.md5 2>/dev/null && echo "Successful test of MD5" || echo "Failed test of MD5" /root.dev/squashfs.img: OK /root.dev/squashfs.o: OK Successful test of MD5 jbusch@jared:~$ md5sum -c /config/good.md5 > /dev/null && echo "Successful test of MD5" || echo "Failed test of MD5" Successful test of MD5 -
Argh, I must be getting tired.
The 2 is good but not what we wanted. Just drop the 2 completely. Just >/dev/null
-
That's better, no extraneous junk. Just pass or fail.
-
Now if you want to run that every five minutes or hourly or daily or whatever you can pop it into the crontab and it will run it for you.
-
@scottalanmiller said:
Argh, I must be getting tired.
The 2 is good but not what we wanted. Just drop the 2 completely. Just >/dev/null
I did. if you look again. And I even recalled the piping output to dev.null once i seen it fail. Like, oh yeah, I learned this a time or three..
-
@scottalanmiller said:
Now if you want to run that every five minutes or hourly or daily or whatever you can pop it into the crontab and it will run it for you.
Yeah, I am thinking weekly to /var/log/ or something on success and the log and email on a problem.
But, now that I am this far on it, I want to look at not having to create the good.md5 on each ERL and after every upgrade (because the value will change). SO, I may need an actual bash script.
But that is not for tonight.
-
Posted over on the UBNT forums.. We'll see what happens. I am heading to bed i think.
-
Good night.
