Add 2.5" U.2 (NVMe) SSDs to custom build?
-
@biggen said in Add 2.5" U.2 (NVMe) SSDs to custom build?:
Yeah I wanted U.2 simply because I like the "physical rectangular" drive and it can be slipped in and out of that ICY DOCK drive tray without having to break open the case to swap a drive out (although I can't imagine I'd be doing this ever). With M.2, you have to screw them in and they just feel "flimsy" to me. Again, this was a lab so I'm not too worried about reliability. Just wanted functionality.
There are also some speed differences if your're concerned with IOPS (as far as the Samsung Data Center drives are concerned) where the U.2 NVMe drives seem to be a bit faster than their M.2 counterparts.
Yes U.2 are usually faster but the real difference is that they are faster with intensive workloads because the U.2 drives can stay cool while the M.2 drives get hot and have to slow down.
The question is what drives did you have in mind? While small capacity U.2 drives were made in the past, now they usually aren't available in smaller capacities than 1TB.
-
@Pete-S
Well before @scottalanmiller ruined my life I was looking at twin MZ-QLB1T9NE.
But that was also before I had to figure spending another $600+ on bays/HBA/cables etc. I was figuring I could get a cheap HBA off Amazon.
I'll have close to $1500 in the system in just drives. Seems a bit silly for a lab of parts at this point.
-
@biggen said in Add 2.5" U.2 (NVMe) SSDs to custom build?:
With M.2, you have to screw them in and they just feel "flimsy" to me. Again, this was a lab so I'm not too worried about reliability. Just wanted functionality.
They are quite solid. but that same Icy Dock unit takes M.2 drives as well.
-
@biggen said in Add 2.5" U.2 (NVMe) SSDs to custom build?:
I'll have close to $1500 in the system in just drives. Seems a bit silly for a lab of parts at this point.
unless NVMe itself is something you are labbing... stick with spinners or really cheap SSDs in a lab.
-
@scottalanmiller I saw that but I still have the problem of what do I plug the "backplane" into.
All I can find are $400+ adapters. -
So I'm looking at the motherboard I'm pillaging from another system and it has two M.2 slots built into it! Doh! When I bought it last year I must have had a premonition I wanted a dual NVMe setup for a future lab!
-
@biggen said in Add 2.5" U.2 (NVMe) SSDs to custom build?:
So I'm looking at the motherboard I'm pillaging from another system and it has two M.2 slots built into it! Doh! When I bought it last year I must have had a premonition I wanted a dual NVMe setup for a future lab!
Scott is right. Putting U2 drives in your build is like Ferrari suspension on a Prius.
And that MB can't take enterprise M2 drives so you're better of with consumer drives.The IcyDoc you're looking at isn't really suitable for U.2 because you need server level cooling over the drives.
That said U.2 doesn't need a hot swap backplane because it's possible to cable them up similar to a SATA drive. Problem with that motherboard is that you need two available slots with x4 PCIe and that one doesn't have it. Or you can hook up two PCIe drives to one x8 or larger PCI slot - if you have bifurbication support on your PCIe slots and consumer motherboards usually don't have that.
-
@Pete-S Yeah I think I'll skip U.2.
ICY DOCK makes this bay that you can put twin M.2 drives in. Then I could run double SFF-8643 cables back to two of these adapters that would plug into the twin M.2 slots on the MB.
All that really gets me is a lot of links and drive trays. Might as well plug the M.2 drives right into the MB and be done with it. I was hoping to buy an Enterprise M.2 drive, though, but those are all 110cm in length and the MB only supports M.2 to 80cm.
Always something...
-
@biggen said in Add 2.5" U.2 (NVMe) SSDs to custom build?:
@Pete-S Yeah I think I'll skip U.2.
ICY DOCK makes this bay that you can put twin M.2 drives in. Then I could run double SFF-8643 cables back to two of these adapters that would plug into the twin M.2 slots on the MB.
All that really gets me is a lot of links and drive trays. Might as well plug the M.2 drives right into the MB and be done with it. I was hoping to buy an Enterprise M.2 drive, though, but those are all 110cm in length and the MB only supports M.2 to 80cm.
Always something...
Actually with those adapters you have another option for U.2 drives. Remember that NVMe is a bus connection so these adapters have no electronics inside.
You put two of the adapters in the two M.2 slots and mount the U.2 drives internally in 2.5" slots. No hotswap but you can easily cold swap. The only thing you need are the right cables.
You have both that card and cable below.
https://www.amazon.com/ASHATA-Connecting-Transfer-Interface-Motherboard/dp/B084X5R47K/
You don't have to take into account any compatibility crap on the amazon page. This entire thing is just a electrical extension of the PCIe bus to the U2 drive.Also make life easier by booting on a regular SSD or satadom.
-
Regarding drives you could have also have a look at Samsung PM983 and Intel P4510. Those are the read intensive (~1DWPD) U2 options from the two largest enterprise SSD manufacturers. Samsung being the cheaper option in this match up.
-
@Pete-S said in Add 2.5" U.2 (NVMe) SSDs to custom build?:
Intel P4510
Yup that would work. Wish I could figure out a way to at least mount the U.2 drives in the 3.5" external drive bay since I don't need a 3.5" bay for anything else. ICY DOCK makes a twin 2.5" SATA drive bay that fits in a 3.5" bay, but they don't make a twin 2.5" U.2 NVMe drive bay that fits in the 3.5". I'm guessing the 2.5" U.2 needs either more spacing or better cooling than a standard 2.5" SATA SSD.
-
@biggen said in Add 2.5" U.2 (NVMe) SSDs to custom build?:
@Pete-S said in Add 2.5" U.2 (NVMe) SSDs to custom build?:
Intel P4510
Yup that would work. Wish I could figure out a way to at least mount the U.2 drives in the 3.5" external drive bay since I don't need a 3.5" bay for anything else. ICY DOCK makes a twin 2.5" SATA drive bay that fits in a 3.5" bay, but they don't make a twin 2.5" U.2 NVMe drive bay that fits in the 3.5". I'm guessing the 2.5" U.2 needs either more spacing or better cooling than a standard 2.5" SATA SSD.
You don't want them in an external bay. Remember that these are PCIe bus connections so it makes sense to have short cables. The cables in the adapter above are probably 1.5 feet at the most.
U.2 drives are thicker than standard SSDs, usually 15mm (a little more than 1/2 inch). They get hotter than normal SSDs but nothing extreme. P4510 for instance is rated at 16W power consumption. Which is about twice as much as a 3.5" spinner. In a high powered rack server the drives stays cool but they're usually designed to have a generous amount of airflow through the case and over the drives.
PS. If it wasn't clear - U.2 drives have the same mechanical mount as 2.5" drives. So you can mount them in a 2.5" internal drive bay or in a 3.5" internal drive bay with adapters. You just can't put them in a hotswap drive bay or any drive bay that has an SATA or SAS backplane because it's electrically not the same.
