EdgeRouter 4: setting up L2TP server

FATeknollogee

C'mon, where are all the ER experts?

JaredBusch

@FATeknollogee said in EdgeRouter 4: setting up L2TP server:

C'mon, where are all the ER experts?

Super busy.

This is a known (to me) issue on the ER line if there are no S2S

I do not recall the solution off the top of my head. I have fixed it before.

FATeknollogee

@JaredBusch Thx for that heads up! Will try searching, maybe I'll get lucky!

JaredBusch

When I was debugging this, I found that it was not getting a valid cipher or something I believe.

FATeknollogee

I just might have to put in some "fake" S2S config & move on?

FATeknollogee

It's strange that UBNT's docs/guides say nothing about this being an issue?

JaredBusch

https://www.mangolassi.it/topic/16505/edgerouter-l2tp-vpn-does-not-work-with-updated-systems

https://community.ui.com/questions/L2TP-unusable-on-Fedora/d91fb0a7-0507-4c6d-be7f-259d2df8edc4

FATeknollogee

There as to be a line in the S2S config that "triggers" the VPN service ON?

FATeknollogee

Figured out the issue:

Even though I copied/paste from here: https://help.ubnt.com/hc/en-us/articles/204950294-EdgeRouter-L2TP-IPsec-VPN-Server

Looks like rule 30 did not copy correctly & I end up with the check mark - State "Invalid".

Once, I unchecked "Invalid", VPN connects fine.

Tomorrow, I'll wipe out the config & re-copy the rules, just to make sure I didn't mess up.

FATeknollogee

I reset the ER4 to factory default & started from scratch.

Copy/paste (from UBNT site) of rule 30, does indeed set the "Invalid" check mark on the Advanced tab of Rule 30

Dashrender

@FATeknollogee said in EdgeRouter 4: setting up L2TP server:

I reset the ER4 to factory default & started from scratch.

Copy/paste (from UBNT site) of rule 30, does indeed set the "Invalid" check mark on the Advanced tab of Rule 30

can you post the whole config?
or is it already above?

FATeknollogee

@Dashrender

firewall {
    all-ping enable
    broadcast-ping disable
    group {
        address-group trusted_IPs {
            address 1.2.3.4
            address 5.6.7.8
            address 9.10.11.12
            description "for remote GUI access"
        }
    }
    ipv6-name WANv6_IN {
        default-action drop
        description "WAN inbound traffic forwarded to LAN"
        enable-default-log
        rule 10 {
            action accept
            description "Allow established/related sessions"
            state {
                established enable
                related enable
            }
        }
        rule 20 {
            action drop
            description "Drop invalid state"
            state {
                invalid enable
            }
        }
    }
    ipv6-name WANv6_LOCAL {
        default-action drop
        description "WAN inbound traffic to the router"
        enable-default-log
        rule 10 {
            action accept
            description "Allow established/related sessions"
            state {
                established enable
                related enable
            }
        }
        rule 20 {
            action drop
            description "Drop invalid state"
            state {
                invalid enable
            }
        }
        rule 30 {
            action accept
            description "Allow IPv6 icmp"
            protocol ipv6-icmp
        }
        rule 40 {
            action accept
            description "allow dhcpv6"
            destination {
                port 546
            }
            protocol udp
            source {
                port 547
            }
        }
    }
    ipv6-receive-redirects disable
    ipv6-src-route disable
    ip-src-route disable
    log-martians enable
    name WAN_IN {
        default-action drop
        description "WAN to internal"
        rule 10 {
            action accept
            description "Allow established/related"
            state {
                established enable
                related enable
            }
        }
        rule 20 {
            action drop
            description "Drop invalid state"
            state {
                invalid enable
            }
        }
    }
    name WAN_LOCAL {
        default-action drop
        description "WAN to router"
        rule 10 {
            action accept
            description "remote GUI"
            destination {
                port 443
            }
            log disable
            protocol tcp
            source {
                group {
                    address-group trusted_IPs
                }
            }
        }
        rule 20 {
            action accept
            description "Allow established/related"
            state {
                established enable
                related enable
            }
        }
        rule 30 {
            action accept
            description ike
            destination {
                port 500
            }
            log disable
            protocol udp
            state {
                invalid enable
            }
        }
        rule 40 {
            action accept
            description esp
            log disable
            protocol esp
        }
        rule 50 {
            action accept
            description nat-t
            destination {
                port 4500
            }
            log disable
            protocol udp
        }
        rule 60 {
            action accept
            description l2tp
            destination {
                port 1701
            }
            ipsec {
                match-ipsec
            }
            log disable
            protocol udp
        }
    }
    receive-redirects disable
    send-redirects enable
    source-validation disable
    syn-cookies enable
}
interfaces {
    ethernet eth0 {
        address 10.10.10.10/30
        description Internet
        duplex auto
        firewall {
            in {
                ipv6-name WANv6_IN
                name WAN_IN
            }
            local {
                ipv6-name WANv6_LOCAL
                name WAN_LOCAL
            }
        }
        speed auto
    }
    ethernet eth1 {
        address 10.15.20.254/24
        description "LAN 1"
        duplex auto
        speed auto
    }
    ethernet eth2 {
        address 192.168.2.254/24
        description "LAN 2"
        duplex auto
        speed auto
    }
    ethernet eth3 {
        duplex auto
        speed auto
    }
    loopback lo {
    }
}
port-forward {
    auto-firewall enable
    hairpin-nat disable
    wan-interface eth0
}
service {
    dhcp-server {
        disabled false
        hostfile-update disable
        shared-network-name LAN2 {
            authoritative enable
            subnet 192.168.2.0/24 {
                default-router 192.168.2.254
                dns-server 192.168.2.254
                lease 86400
                start 192.168.2.38 {
                    stop 192.168.2.43
                }
            }
        }
        static-arp disable
        use-dnsmasq disable
    }
    dns {
        forwarding {
            cache-size 10000
            listen-on eth1
            listen-on eth2
            name-server 1.1.1.1
            name-server 9.9.9.9
        }
    }
    gui {
        http-port 80
        https-port 443
        older-ciphers enable
    }
    nat {
        rule 5010 {
            description "masquerade for WAN"
            outbound-interface eth0
            type masquerade
        }
    }
    ssh {
        port 22
        protocol-version v2
    }
    unms {
        connection wss://
    }
}
system {
    domain-name ubnt
    gateway-address 10.10.10.1
    host-name ER4
    login {
        user ubnt {
            authentication {
                encrypted-password ubnt
            }
            level admin
        }
    }
    name-server 1.1.1.1
    name-server 9.9.9.9
    ntp {
        server 0.ubnt.pool.ntp.org {
        }
        server 1.ubnt.pool.ntp.org {
        }
        server 2.ubnt.pool.ntp.org {
        }
        server 3.ubnt.pool.ntp.org {
        }
    }
    offload {
        hwnat disable
        ipsec disable
    }
    syslog {
        global {
            facility all {
                level notice
            }
            facility protocols {
                level debug
            }
        }
    }
    time-zone UTC
}
vpn {
    ipsec {
        allow-access-to-local-interface disable
        auto-firewall-nat-exclude disable
        ipsec-interfaces {
            interface eth0
        }
    }
    l2tp {
        remote-access {
            authentication {
                local-users {
                    username hello {
                        password 1234
                    }
                }
                mode local
            }
            client-ip-pool {
                start 192.168.100.100
                stop 192.168.100.110
            }
            dns-servers {
                server-1 1.1.1.1
                server-2 9.9.9.9
            }
            idle 1800
            ipsec-settings {
                authentication {
                    mode pre-shared-secret
                    pre-shared-secret 1234
                }
                ike-lifetime 3600
                lifetime 3600
            }
            mtu 1492
            outside-address 10.10.10.10
        }
    }
}