Building Out XenServer 6.5 with USB Boot and Software RAID 10

Romo

Quite strange that the first two entries don't have a UUID set, mdadm needs the UUID set.

We could try to manually edit the file, adding the UUID from the last entry into the first entry, and then removing entries 2 and 3.

DustinB3403

@Romo Like so?

[root@eaglexen-baby mnt]# cat /etc/mdadm.conf 
ARRAY /dev/md0 level=raid10 num-devices=4 metadata=1.2 name=eaglexen-baby:0 UUID=5bd9375b:2166352e:622be934:4b65a7ea
   devices=/dev/sdb,/dev/sdc,/dev/sdd,/dev/sde metadata=1.2  name=eaglexen-baby:0
[root@eaglexen-baby mnt]#

Romo

@DustinB3403 said:

ARRAY /dev/md0 level=raid10 num-devices=4 metadata=1.2 name=eaglexen-baby:0 UUID=5bd9375b:2166352e:622be934:4b65a7ea
devices=/dev/sdb,/dev/sdc,/dev/sdd,/dev/sde metadata=1.2 name=eaglexen-baby:0

ARRAY /dev/md0 level=raid10 num-devices=4 metadata=1.2 name=eaglexen-baby:0 UUID=5bd9375b:2166352e:622be934:4b65a7ea
devices=/dev/sdb,/dev/sdc,/dev/sdd,/dev/sde

Romo

Don't need the metadata and name again after the devices

DustinB3403

[root@eaglexen-baby mnt]# cat /etc/mdadm.conf 
ARRAY /dev/md0 level=raid10 num-devices=4 metadata=1.2 name=eaglexen-baby:0 UUID=5bd9375b:2166352e:622be934:4b65a7ea devices=/dev/sdb,/dev/sdc,/dev/sdd,/dev/sde

Romo

Yes, seems ok. Reboot and try to check the status of the array once again

DustinB3403

@Romo said:

Yes, seems ok. Reboot and try to check the status of the array once again

Rebooted.

Array found, drives mounted.

DustinB3403

So now that we're back to working condition. We need an entry added to fstab to auto-mount the array.

  GNU nano 1.3.12             File: /etc/fstab                                  

LABEL=root-mhdhrpdq    /         ext3     defaults   1  1
/var/swap/swap.001          swap      swap   defaults   0  0
none        /dev/pts  devpts defaults   0  0
none        /dev/shm  tmpfs  defaults   0  0
none        /proc     proc   defaults   0  0
none        /sys      sysfs  defaults   0  0
none        /sys/fs/cgroup cgroup memory 0 0
/opt/xensource/packages/iso/XenCenter.iso   /var/xen/xc-install   iso9660   loo$
/mnt/raid10   /dev/md0  ext3  defaults 0  0

Romo

Does xencenter see the storage?

DustinB3403

Yes, the Local OBR10 is back on XenCenter.

Romo

@DustinB3403 Not so sure about the entry on fstab, I don't have the entry in my setup and xen properly automounts it

DustinB3403

@Romo It's outside of the norm for XenServer.

Even if it's benign.

XenServer by default, doesn't say "oh yeah go build an mdadm array" because it's not ideal if you can avoid it.

Romo

@DustinB3403 said:

@Romo It's outside of the norm for XenCenter.

Even if it's benign.

Yes indeed.

Alex Sage

This post is deleted!

Alex Sage

This post is deleted!

Alex Sage

Looks good?

[root@XenServer ~]# cat /proc/mdstat
Personalities : [raid10] [raid1]
md0 : active raid1 sdb[0] sdc[1]
      976631360 blocks super 1.2 [2/2] [UU]
      [=>...................]  resync =  5.4% (52749312/976631360) finish=143.3min speed=107400K/sec

unused devices: <none>
[root@XenServer ~]#

DustinB3403

@anonymous besides just the two disk, yeah it looks alright.

scottalanmiller

Nothing wrong with RAID 1!

Alex Sage

Will this guide work with CentOS 7?

DustinB3403

@aaronstuder said:

Will this guide work with CentOS 7?

It likely would, but you'll have to test it to find out.