Ubiquiti wifi bridge static on VoIP calls
-
That was pinging the AP on the other side of the bridge. I hooked my laptop up to the far side and pinged back to the router at HQ. No drops, but I think it's weird that there was any pings above 1ms since I'm the only one on it. I think when I dropped the channel width down to 20MHz they were all consistent at 1ms. Is there an explanation for that? I don't really understand the theory behind that one.
Ping statistics for 192.168.1.2:
Packets: Sent = 459, Received = 459, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 74ms, Average = 2ms -
@Mike-Davis said in Ubiquiti wifi bridge static on VoIP calls:
Both are mounted to the building like this. It doesn't seem like they can move.
The correct mount for this type things is a very sold mast (or schedule pipe) and an clamp around the pipe, something like that will move out of alignment.
-
@Mike-Davis said in Ubiquiti wifi bridge static on VoIP calls:
That was pinging the AP on the other side of the bridge. I hooked my laptop up to the far side and pinged back to the router at HQ. No drops, but I think it's weird that there was any pings above 1ms since I'm the only one on it. I think when I dropped the channel width down to 20MHz they were all consistent at 1ms. Is there an explanation for that? I don't really understand the theory behind that one.
Ping statistics for 192.168.1.2:
Packets: Sent = 459, Received = 459, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 74ms, Average = 2msThe way I understand it is that the wider the channel, the more chances there are from devices or other things on nearby channels... Just like when running at 2.4gHz (these are 5gHz units, right?).
For the wireless N units that I last set up (5 years ago), we used the 20 mHz channel width all the way around.
-
yes, they are 5GHz. I don't need the bandwidth at 80mHz, so maybe I'll try knocking it down and seeing how that goes. From what I read the lower frequencies are less suseptable to interference. Does anyone have any real world experience of that? Also what is the "constellation" tool supposed to look like when things are good vs bad? I ran it, but then didn't know what I was looking at.
-
@Mike-Davis What your reading is correct, but that's the physical radio signal. A 10MHz signal can more easily pass through walls than a 10GHz signal, which while correct, isn't what most people refer to when talking about wifi. Lots of things can interfere with the 2.4GHz wifi signals. Less things use the 5GHz range, so that channel is normally more available.
-
I knocked it down to 20MHz channel width and ran it for 14 hours with no pings over 20 ms. Users have been on it for 2 work days now and everything is working fine. I wish I understood the science behind it so I could know definitively if I moved the second antenna higher on the building if I could get more bandwidth out if it, but at the speed it's running now, it really doesn't matter. They have more than enough bandwidth and it seems to be solid, so I'm going to leave well enough alone.
-
@Mike-Davis said in Ubiquiti wifi bridge static on VoIP calls:
I knocked it down to 20MHz channel width and ran it for 14 hours with no pings over 20 ms. Users have been on it for 2 work days now and everything is working fine. I wish I understood the science behind it so I could know definitively if I moved the second antenna higher on the building if I could get more bandwidth out if it, but at the speed it's running now, it really doesn't matter. They have more than enough bandwidth and it seems to be solid, so I'm going to leave well enough alone.
glad this worked out for you
-
@Mike-Davis said in Ubiquiti wifi bridge static on VoIP calls:
I knocked it down to 20MHz channel width and ran it for 14 hours with no pings over 20 ms. Users have been on it for 2 work days now and everything is working fine. I wish I understood the science behind it so I could know definitively if I moved the second antenna higher on the building if I could get more bandwidth out if it, but at the speed it's running now, it really doesn't matter. They have more than enough bandwidth and it seems to be solid, so I'm going to leave well enough alone.
If it ain't broke, don't fix it, lol. Glad you got it sorted!
-
Woot!
-
@Mike-Davis said in Ubiquiti wifi bridge static on VoIP calls:
I knocked it down to 20MHz channel width and ran it for 14 hours with no pings over 20 ms. Users have been on it for 2 work days now and everything is working fine. I wish I understood the science behind it so I could know...
You could always try to go on a Ubiquiti training course for this kind of thing. - Depends on the location.