LAN speed
-
You can check by looking at the LEDs on the front of the switch port. If one is a solid green it is 1Gb/s if it is yellow then it is 100Mb/s.
-
it is blue Sir, all 4 are blue
-
Did the NAS come with the Drives, or did you purchase them separately?
Do you know what model hard drives is in the NAS?
-
@IT-ADMIN said:
it is blue Sir, all 4 are blue
On the Cisco Switch? Where the cables plug in? Not the other side (assuming there are lights on the other side).
-
Oh man... it looks like Solid blue indicates the port is running at 10Mb/s (If I'm reading the right documentation) if the duplex LED is also blue then you are running at half duplex.
-
@coliver said:
Oh man... it looks like Solid blue indicates the port is running at 10Mb/s (If I'm reading the right documentation) if the duplex LED is also blue then you are running at half duplex.
Hopefully that's not right - since he did indicate that he checked on the server NIC status and it told him he was running at 1 Gb.
-
@IT-ADMIN said:
NAS WD my cloud EX4 12 TB
The documentation here PDF jump to Page 125 has all of the network information for this system.
So it's easily confirm-able if this unit is set for Half or Full Duplex, as well as the speed of the NAS NIC.
-
@Dashrender said:
@IT-ADMIN said:
it is blue Sir, all 4 are blue
On the Cisco Switch? Where the cables plug in? Not the other side (assuming there are lights on the other side).
yeah i'm talking about the NAS LEDs not the switch LEDs,
the switch LEDs are green -
@IT-ADMIN said:
@Dashrender said:
@IT-ADMIN said:
it is blue Sir, all 4 are blue
On the Cisco Switch? Where the cables plug in? Not the other side (assuming there are lights on the other side).
yeah i'm talking about the NAS LEDs not the switch LEDs,
the switch LEDs are greenOk, that's good. If they are a solid green then you are running at 1Gb/s at the switch.
-
Can you go into the network page on the NAS, and screen shot that for us?
I have a feeling the speed within the NAS is set to Auto. Which if it is, is likely causing the performance of the NIC to be slow. So either there is something wrong with the configuration on your Switch. Or the NAS.
-
the front side of the NAS itself has LED above each HD, i thought you are talking about them
-
@IT-ADMIN said:
the front side of the NAS itself has LED above each HD, i thought you are talking about them
Those LED are status indicators of the drives them selves, not the performance of the NIC connected to the back of the NAS.
-
@DustinB3403 said:
Can you go into the network page on the NAS, and screen shot that for us?
I have a feeling the speed within the NAS is set to Auto. Which if it is, is likely causing the performance of the NIC to be slow. So either there is something wrong with the configuration on your Switch. Or the NAS.
yes you are right, the link speed is set to auto, should i change it to 1000 ??
-
-
Yes, but be warned.
If for some reason that the speed isn't supported on your switch, you'll likely be unable to manage the NAS without performing a factory reset on it.
It should be supported, but it sounds as if the NAS is connected at 100MB.
Confirm that you can connect to the NAS directly via direct Ethernet before making the switch to 1000MB/s in case you must change it back.
-
thank you for your advice, but the cisco switch (catalyst 3560) is 1 Gb/s, this is for sure
-
It's been a while since I've seen auto not work as advertised,
So I ask - is it still best practice to manually set the switch and server manually to the desired speed and duplex?
-
so what do you think guys ?? should i change it to 1000 ??
-
@Dashrender It's never a best practice, but to pinpoint causes of trouble sometimes you must.
@IT-ADMIN can you confirm that you can access the NAS with the second port or a cross-over cable. We don't want you to have to perform a factory reset unnecessarily.
-
did the factory reset delete the data ?? or just reset the setting ??
