Hyper-V Failover Live Migration failed. Error 21502
-
@LAH3385 said:
EDIT: Just to be clear when I first started the troubleshooting I had 1 problem. After the first problem cleared I encountered with the second problem. So if you skim through the thread you may get confused very quickly.
I have been trying to configure a vSAN by StarWind with 2 node for the past weeks. With multiple guides and help from the community, still I cannot test LIVE MIGRATION. Quick Migration does works so I do not quite understand Why?
note: Quick Migration works. Force migration via restarting the server works. Live Migration failed confused
**> From my initial research I know the cause is probably something to do with setting or naming. Something is not identical and is causing the failure between the node. I configure the server mirroring each other from scratch and still the problem exist. **
Here are some screenshots. [ ... ]
@LAH3385 Sorry for being late on party - I was quite busy with closing our year of 2015 to spend time with MangoHeads
Either way there's no point to be shy - you know my e-mail address so there's an easy way to get your questions answered. For now I'm brining in StarWind engineers to see what's up with your case as I'm still head over heals till January 15th, 2016.@scottalanmiller Thanks for letting me know !!
-
Hi guys!
@scottalanmiller , thanks for bringing me in
@LAH3385 on my experience that happens due to some not obvious, but really tiny misconfiguration. Like wrong partitioning, not configured MPIO, etc.
It's not like I do want to highjack this thread, but it would be much easier for me to resolve this if we could jump on the remote session. Is that actually possible? If so, then let's schedule one (email me to [email protected]) and me or you, or both of us gonna post an update for the community after. Do we have a deal?:) -
I thought the issue was resolved?
-
@Dashrender said:
I thought the issue was resolved?
Well, I am responsible for customer care, so I want to be completely sure
-
@original_anvil
The issue is resolved. However I am experiencing another "problem". I don't want to call it an issue since it does not prohibit the VM server from functioning, nor Failover to fail. I am using the VM servers as file server and some accounting application. I cannot seem to make the network bandwidth as stable as it is on physical server.
On a test 5GB file transfer between my PC to VM server, the transfer rate fluctuated between 7MB to 11MB. Some time as low as 4MB
On the same test between my PC to physical server, the transfer rate is steady at 11MB.
It is not much but for 70 users it might cause performance issue. Any idea? -
@LAH3385 said:
@original_anvil
The issue is resolved. However I am experiencing another "problem". I don't want to call it an issue since it does not prohibit the VM server from functioning, nor Failover to fail. I am using the VM servers as file server and some accounting application. I cannot seem to make the network bandwidth as stable as it is on physical server.
On a test 5GB file transfer between my PC to VM server, the transfer rate fluctuated between 7MB to 11MB. Some time as low as 4MB
On the same test between my PC to physical server, the transfer rate is steady at 11MB.
It is not much but for 70 users it might cause performance issue. Any idea?What is your network setup?
What NICs are doing the disk replication between the servers? Is the network and the vSAN traffic on the same switch (or are you using cross over cables?)? -
Server(VM server) > Cisco(1GB) > patch panel > my PC
Server has 4 ethernet ports. Port 1 is connected to Cisco switch. Port 3&4 is connected between the 2 failover servers via cross-over cable. -
What's the saturation level on 3&4? Are the linked into a single pipe?
-
@Dashrender
How do I check that? -
@LAH3385 said:
@Dashrender
How do I check that?I'd start by opening task manager and seeing how the graphs look for those interfaces - I'm not how how to setup NIC teaming - though with Server 2012 it's supposed to be pretty easy.
-
@Dashrender
I really do not know what am I looking for. The first three are physical. The last one is VM.
-
@LAH3385 said:
@Dashrender
I really do not know what am I looking for. The first three are physical. The last one is VM.You mean the first three are the NICs in the Hyper-Visor, and the last one is the VM?
Ok the second and third look linked.
-
@Dashrender
Yes. that is correct. -
Those numbers look good. Move a huge file (at least 2 GB, though it might need to be more like 4 or 6 GB so the transfer lasts long enough) from the server and take screen shots after about 30 seconds in, then move from the workstation to the server, again take screen shots about 30 seconds in.
-
@Dashrender
First screenshot 5GB. transfer rate 8MB/s - 12MB/s
Second screenshot 5GB. transfer rate steady 10.5MB/s - 12MB/s
-
@LAH3385 That's the sort of max transfer speed I'd expect out of a 100 megabit network. Something is probably not set or working right with the crossover connections.
-
@travisdh1
Beside setting static ip address I did not do anything more than that. (aside from starwind vSAN) -
Thanks - and while these graphs might be useful, I was really hoping to see the ones you posted earlier, from Task Manager, showing each of the NICs.
-
@Dashrender
it's a 10 minute transfer. The graph only shows a minute(?). Beside I think it should maxed out anyhow. Also, because I transfer the file across the network it doesn't utilize cross-over network. -
@LAH3385 said:
@Dashrender
it's a 10 minute transfer. The graph only shows a minute(?). Beside I think it should maxed out anyhow. Also, because I transfer the file across the network it doesn't utilize cross-over network.it should use the cross over cable because the data should be replicated between the StarWinds vSAN, assuming the data is being written to a partition on that volume, which was where I thought your bottleneck might be.
Also, as travishdh mentioned - is your switch a 100 Mb switch?
