What Makes Parity RAID Safe on SSDs
-
@stacksofplates said in What Makes Parity RAID Safe on SSDs:
This is also why I have a couple of older servers with RAID 5 that I will be decommissioning this year but haven't removed the RAID 5 from. They are 10K 146GB SAS drives, so the chances of hittiting a URE during a rebuild are low enough.
LOL - I'm in this same boat. I removed an old server from service with 300 GB drives about a month ago. I wasn't worried about it for the same reason - two RAID 5 arrays, each with three drives (yeah don't ask I didn't build it.).
-
@Dashrender said in What Makes Parity RAID Safe on SSDs:
OK I had to do some digging before posting.
I recall seeing @scottalanmiller post many times that SSDs don't suffer UREs, but perhaps he was meaning that they are so unlikely in current use patterns we can ignore them.
http://www.theregister.co.uk/2015/05/07/flash_banishes_the_spectre_of_the_unrecoverable_data_error/
This post talks about this topic exactly. But I'll shorten it for this post.
https://i.imgur.com/JfTT7E0.pngYou asked - is it all about the bits, yep, it sure is. As you can see in that graphic, even consumer SSDs are 10x less likely to hit a URE than an enterprise HDD. And there are two levels greater than that. You can see where Scott got the 12 TB basically means 100% likeliness that a resilver will fail. You'll notice that a 600 TB array has about a 50% chance of failure, 300 TB has 25% 100 TB is around 8%.
I think the new question we need to ask ourselves, what level of risk are we willing to accept? Which isn't new at all, it's something we should have been (and continue) to ask ourselves.
Don't take those numbers for granted, there are plenty of consumer SSD drives with 10^14 URE. So if you happen to put 6x 2TB SSDs in RAID 5, you can still run into it.
Now another thing is most misunderstand what URE is and assume it's a set number and you always hit URE after reading 12.5 TB. It's not, it's just a probability or running into sector on disk that cannot be read from. Similar to playing Russian Roulette, if you're lucky, you can keep pulling the trigger indefinitely without blowing your brains out, you can have RAID 5 rebuilding PBs of data without ever hitting URE. -
@marcinozga said in What Makes Parity RAID Safe on SSDs:
Now another thing is most misunderstand what URE is and assume it's a set number and you always hit URE after reading 12.5 TB. It's not, it's just a probability or running into sector on disk that cannot be read from. Similar to playing Russian Roulette, if you're lucky, you can keep pulling the trigger indefinitely without blowing your brains out, you can have RAID 5 rebuilding PBs of data without ever hitting URE.
That's why it's a percentage risk number. Otherwise an array of 12.5TB would have a 100% failure rate, but that never quite happens. There is never 100% success nor 100% failure no matter how big or small the array. But it gets really high, really quickly.
-
@scottalanmiller said in What Makes Parity RAID Safe on SSDs:
@marcinozga said in What Makes Parity RAID Safe on SSDs:
Now another thing is most misunderstand what URE is and assume it's a set number and you always hit URE after reading 12.5 TB. It's not, it's just a probability or running into sector on disk that cannot be read from. Similar to playing Russian Roulette, if you're lucky, you can keep pulling the trigger indefinitely without blowing your brains out, you can have RAID 5 rebuilding PBs of data without ever hitting URE.
That's why it's a percentage risk number. Otherwise an array of 12.5TB would have a 100% failure rate, but that never quite happens. There is never 100% success nor 100% failure no matter how big or small the array. But it gets really high, really quickly.
I can honestly say in the dozen or so RAID-5 rebuilds that I've seen in the last 6 years, literally half of them were successful, and the other half were not. This was in arrays of 6 x 250GB drives to 8 x 1TB drives (all Winchester / spinning rust).
-
@dafyre How many of the failed ones were actually caused by URE? I'd be interested to see the %.
-
@marcinozga said in What Makes Parity RAID Safe on SSDs:
@dafyre How many of the failed ones were actually caused by URE? I'd be interested to see the %.
That I can't tell you. Drive "help me" lights came on, and we replaced drives.
At one point, with one of our LeftHand SANs, I was sent 8 brand new drives, as the techs saw severe errors on all 8 of them, lol. I had to re-install the LeftHand OS from scratch and let that thing sync with our other unit across the way. Only took a week to sync 7TB... The upshot is that nothing went down or slowed to a crawl.
-
If I'm thinking about this correctly, a help me light is a failed/failing drive, not usually a URE. Single UREs happen all the time but don't take the drive down/offline.
This kinda tells me that the lights indicate drive failures.
-
@dafyre said in What Makes Parity RAID Safe on SSDs:
@scottalanmiller said in What Makes Parity RAID Safe on SSDs:
@marcinozga said in What Makes Parity RAID Safe on SSDs:
Now another thing is most misunderstand what URE is and assume it's a set number and you always hit URE after reading 12.5 TB. It's not, it's just a probability or running into sector on disk that cannot be read from. Similar to playing Russian Roulette, if you're lucky, you can keep pulling the trigger indefinitely without blowing your brains out, you can have RAID 5 rebuilding PBs of data without ever hitting URE.
That's why it's a percentage risk number. Otherwise an array of 12.5TB would have a 100% failure rate, but that never quite happens. There is never 100% success nor 100% failure no matter how big or small the array. But it gets really high, really quickly.
I can honestly say in the dozen or so RAID-5 rebuilds that I've seen in the last 6 years, literally half of them were successful, and the other half were not. This was in arrays of 6 x 250GB drives to 8 x 1TB drives (all Winchester / spinning rust).
That's a rough fail rate.
-
I've been lucky I guess - I've never lost an array when resilvering a RAID 5 array.
-
@marcinozga said in What Makes Parity RAID Safe on SSDs:
@dafyre How many of the failed ones were actually caused by URE? I'd be interested to see the %.
Yeah. RAID fails from so many factors. Often no one records what affected what. We were hit with URE losses on an array that lost zero disks! We never used RAID 5 again
-
@Dashrender said in What Makes Parity RAID Safe on SSDs:
I've been lucky I guess - I've never lost an array when resilvering a RAID 5 array.
Ha, I've been lucky to never use RAID 5
-
@Dashrender said in What Makes Parity RAID Safe on SSDs:
If I'm thinking about this correctly, a help me light is a failed/failing drive, not usually a URE. Single UREs happen all the time but don't take the drive down/offline.
This kinda tells me that the lights indicate drive failures.
URE would never cause a drive failed light as the drive is fine. Light indicators are always failed or failing drives. But a single drive loss would not be what killed the machine, it's a drive loss PLUS a URE that would do it.
-
@scottalanmiller said in What Makes Parity RAID Safe on SSDs:
@dafyre said in What Makes Parity RAID Safe on SSDs:
@scottalanmiller said in What Makes Parity RAID Safe on SSDs:
@marcinozga said in What Makes Parity RAID Safe on SSDs:
Now another thing is most misunderstand what URE is and assume it's a set number and you always hit URE after reading 12.5 TB. It's not, it's just a probability or running into sector on disk that cannot be read from. Similar to playing Russian Roulette, if you're lucky, you can keep pulling the trigger indefinitely without blowing your brains out, you can have RAID 5 rebuilding PBs of data without ever hitting URE.
That's why it's a percentage risk number. Otherwise an array of 12.5TB would have a 100% failure rate, but that never quite happens. There is never 100% success nor 100% failure no matter how big or small the array. But it gets really high, really quickly.
I can honestly say in the dozen or so RAID-5 rebuilds that I've seen in the last 6 years, literally half of them were successful, and the other half were not. This was in arrays of 6 x 250GB drives to 8 x 1TB drives (all Winchester / spinning rust).
That's a rough fail rate.
There for a few years, we had a crazy time with stuff crapping out. Even a new drive array went crazy. After the LeftHand, the RAID 5 rebuilds got better, but still lost far more of them than we should have.
-
@Dashrender said in What Makes Parity RAID Safe on SSDs:
I've been lucky I guess - I've never lost an array when resilvering a RAID 5 array.
I'm not actually 100% sure I've ever seen one recover. Seems like I must have, but I can't actually remember it.
-
@Dashrender Some RAID controllers have certain limit on number of URE they encounter before marking drive as failed. I had that happen on some LSI controllers, but the numbers were really high, perhaps in thousands.
-
@marcinozga said in What Makes Parity RAID Safe on SSDs:
@Dashrender said in What Makes Parity RAID Safe on SSDs:
I've been lucky I guess - I've never lost an array when resilvering a RAID 5 array.
Ha, I've been lucky to never use RAID 5
How long have you been in the game?
-
@Dashrender said in What Makes Parity RAID Safe on SSDs:
@marcinozga said in What Makes Parity RAID Safe on SSDs:
@Dashrender said in What Makes Parity RAID Safe on SSDs:
I've been lucky I guess - I've never lost an array when resilvering a RAID 5 array.
Ha, I've been lucky to never use RAID 5
How long have you been in the game?
Long enough. 17 years if my math is correct. I always managed to push RAID 10 over 5.
-
@marcinozga said in What Makes Parity RAID Safe on SSDs:
@Dashrender said in What Makes Parity RAID Safe on SSDs:
@marcinozga said in What Makes Parity RAID Safe on SSDs:
@Dashrender said in What Makes Parity RAID Safe on SSDs:
I've been lucky I guess - I've never lost an array when resilvering a RAID 5 array.
Ha, I've been lucky to never use RAID 5
How long have you been in the game?
Long enough. 17 years if my math is correct. I always managed to push RAID 10 over 5.
Wow - so back in the late 90's you were able to always justify the price of RAID 10, great. I wasn't - and really it wasn't needed either.
-
@Dashrender I came from heavy gaming background, so performance was always my priority, sometimes the only priority, lol. So RAID 5 was off the table, period. And I was lucky enough to always work for people who had no clue what I was actually doing.
-
@Dashrender said in What Makes Parity RAID Safe on SSDs:
I've been lucky I guess - I've never lost an array when resilvering a RAID 5 array.
Me either, technically.
Though I have lost a good percentage just from plugging the new drive in.
